How To Make Simple Window Shades
Ah, window treatments: They just may be the nearly overlooked part of a home's design. Designers concord they're a foundational part of any room's pattern (after all, they often take up more square footage than annihilation besides the walls and floor covering), still they're often an afterthought in the design process. And while the daunting array of possibilities out there may have you resigned to just throwing up the simplest curtains, you don't have to! If y'all accept a sewing motorcar and a drill at home, you tin make your very own Roman shades. These pleating, string-pulled window coverings are a favorite of high-end designers. And while they may look complex, they're actually not all that complicated to DIY. If you lot have a few hours, the correct tools, and a bit of patience, yous tin can create your own—in any material yous fancy. Later on watching photographer and blogger Lucy Cuneo document her kickoff set on Instagram, nosotros reached out to get the breakdown. Read on for her full tutorial.
What you'll need:
- Fabric
- Lining fabric
- Yardstick
- Sewing machine
- Scissors
- Needle & thread
- Stitch Witchery Fusible Bonding Web
- Centre hooks
- Pins
- Screws
- Forest dowels
- Metal rod
- 2x2 wood slice
- Sew together-on rings
- Drapery cord
- Cord lock
- Staple gun
- Drill
- Iron
How to make Roman shades:
1. Mensurate and prep
Measure out the window where yous desire the bullheaded and cut your fabric 3 inches wider than the window and 6 inches longer. Next, cut your textile liner the same length as the cloth and i inch narrower.
2. Stitch fabric and liner
Lay the fabric face upwards with the liner on top of it (so the pattern side of the fabric is covered). Pin both long siders together and run up, then iron to create the edge of your drapery. Don't flip right side out—yet!
3. Create rod pockets
Cutting your woods dowels to be ane inch narrower than the frame of your window. And so, cut strips of cloth liner a few inches wide. Fold them over, atomic number 26, and sew to create a pocket that will fit the dowels snugly (leaving an inch or two of cloth at the border).
You'll want to place your dowels viii-10 inches apart on your shade, so keeping in heed the total height of your window, space them evenly from the superlative down, leaving an extra inch for at bottom. Mark with a pencil.
four. Attach rod pockets
Attach Stitch Witchery to your rod pocket by placing it atop the fabric and passing an atomic number 26 just above information technology, without actually touching. Then, lay the pocket along the marker y'all've fabricated and fe it onto the curtain with the Stitch Witchery between pocket and pall. Repeat with all rod pockets and then slide the woods dowels in. Once the dowels are secure, flip inside out to reveal the front side of the fabric, with the liner behind it and the dowels inside.
five. Adhere sewing rings
On the back (liner) side, along each dowel, measure out 2 1/2 inches in from the edge and mark with a pencil, then marking the middle point on each. Using a needle and thread, attach sewing rings to the liner at each mark (there should be 9 total!).
6. Finish bottom hem
Fold the bottom material ii ane/ii inches up and sew. So slide in the metal rod to weigh down the bottom of the shade.
7. Finish top
Cut your 2x2 to the width of the inside of your window frame. So, drill three holes in it, aligned with the rings (to attach your curtain with screws to the window frame) and screw an centre claw into one border. Attach the cord lock adjacent to the eye claw, if you want to be able to lock your cord when the shade is open (you can skip this for a shade you'll tie to secure). Place the 2x2 with the center hook on the side where y'all desire your curtain string, and so wrap the elevation of your fabric effectually it and staple in place.
8. Thread string
Run your cord across the peak of the curtain (through the eye hook and lock) and so downwards through the loops on the far side, securing it at the bottom one. Echo this procedure across the top and down the middle row of hooks, securing at the lesser. Finally, thread a third piece of string through the eye hook and downward the last row of hooks, securing at the lesser. Get out two-3 anxiety of string at the non-tied end, then necktie all iii of these ends together in a knot. If you want, add a decorative pull.
9. Install and train
Using a drill, attach the 2x2 to the inside of your window frame with screws through the holes you made. The offset few times you use the blind, "train" it, by gently guiding the pleats as you pull information technology up and down. After a few uses, the pleats will autumn in the proper place. For this non-mechanical have on Roman shades, you'll want to install some hardware to attach the string to when the drape is upward—that can be a hook or knob inside the frame of the window or abreast it.
And voilà—you've got Roman shades!
Desire to start with simpler defunction? Nosotros've got a tutorial for that, too!
Follow House Beautiful on Instagram .
This content is created and maintained by a third political party, and imported onto this page to help users provide their email addresses. You may exist able to notice more information about this and similar content at piano.io
Source: https://www.housebeautiful.com/home-remodeling/diy-projects/a35226507/diy-roman-shades/
Posted by: gilsongrom1954.blogspot.com
0 Response to "How To Make Simple Window Shades"
Post a Comment